Restoring a Ted Williams Model 100 .30-30
by Roy Seifert

See Full List On Gun-data.com
Serial Number Data - ProofHouse.com
Ted Williams Model 100 Serial Number Lookup

Sears has opened the doors to its vast archival collection and invited the public to peek inside. More than 100 years of stories, product and brand histories, photographs, catalog images and more are now available online.

Click here to purchase a CD with this and all Kitchen Table Gunsmith Articles.

Disclaimer:This article is for entertainment only and is not to be used in lieu of a qualified gunsmith.Please defer all firearms work to a qualified gunsmith. Any loads mentioned in this article are my loads for my guns and have been carefully worked up using established guidelines and special tools.The author assumes no responsibility or liability for use of these loads, or use or misuse of this article.Please note that I am not a professional gunsmith, just a shooting enthusiast and hobbyist, as well as a tinkerer.This article explains work that I performed to my guns without the assistance of a qualified gunsmith.Some procedures described in this article require special tools and cannot/should not be performed without them.

I have a Ted Williams, Model 100 lever action 30-30 WInchester. I see that it is a Sears, Roebuck and Co. I've also found that the number is a Sears 'part' number, but the number I've seen (on line) is xxx.xxx140, and my number ends with xxxx141.
Jan 30, 2020 Just like Ted Williams this pump gun has been frozen in time.CA Legal or CA Private Party Transferable: This shotgun can be transferred in California.LSB#: 130308PJ07 Make: Ted Williams (Sears) made by Winchester Model: Model 200 (Winchester Model 1200) Serial Number: 39101 Year of Manufacture: Modern Gaug.
Searching through the used gun rack at my local gun store I found a well-abused Ted Williams model 100.30-30, which I purchased for the very reasonable price of $225. This model is really a Winchester 94 sold by Sears under the Ted Williams name.

Warning:Disassembling and tinkering with your firearm may void the warranty.I claim no responsibility for use or misuse of this article.Again, this article is for entertainment purposes only!

Tools and firearms are the trademark/service mark or registered trademark of their respective manufacturers.

I really enjoy working on a project gun.There’s a tremendous sense of pride in turning a junker into a fine looking and shooting firearm.I recently purchased a saddle and built a saddle stand for it primarily to show off my leatherwork.I wanted a lever-action rifle to display in the scabbard, but found the pewter replicas to be far too expensive at $180-$225.Searching through the used gun rack at my local gun store I found a well-abused Ted Williams model 100 .30-30, which I purchased for the very reasonable price of $225.This model is really a Winchester 94 sold by Sears under the Ted Williams name.With a magazine plug in place and the firing pin disabled, this would make a fine display piece in the leather scabbard mounted on my saddle.

Initial Assessment
This is an example of a no frills, classic, Winchester .30-30.It does not have an external safety other than the half-cock notch on the hammer, nor does it have fancy sights.It has a leaf main spring instead of the coil spring and rebounding hammer.

As mentioned before, this rifle looked like someone had very much abused it.From the amount of surface rust it was probably left in a soft gun case/bag for an extended period.It may also have been left in a closet, as there was white paint on the barrel and magazine tube.The previous owner had engraved his driver’s license number on the bottom tang, which I will have to remove.

It looked like the wood had been replaced and had some nicks and scratches, but was in otherwise excellent condition.The original Sears butt plate did not fit properly as you can see in the above photo.Because the end of the butt stock was wider than the butt plate the stock was prone to chipping.

The fore end had about 1/16 inch play forward and backward as you can see in the above photo.

I think the worst case of abuse I found on this rifle was the front sight.It looked like someone had tried to replace the front sight with a higher one, which did not fit into the dovetail, or they may have removed the front sight to mount a scope, then tried to re-install it when they sold the rifle.Most of the scope mounting hole plug screw slots were buggered.In the photo above you can clearly see the gap below the bottom of the sight.

I scrubbed the bore with Remington Bore Cleaner and fortunately, the bore looked fairly clean and sharp.The lands were nice and sharp at the muzzle, indicating to me that the rifle was not used much, nor cleaned very often.There was, however, some surface rust in the bore.

Restoration Plan
This rifle is not really going to be a shooter, although it could be.It’s mostly for display purposes so I plan to reassemble it so it cannot be fired.However, since I have it apart I’ll do some basic work to it if I ever want it to be a shooter.

Remove the front and rear sights.
Completely disassemble the rifle and check for internal rust/damage.
Unscrew the barrel from the receiver.
Remove the surface rust from the barrel and lever.
Remove DL number, polish and refinish lower tang.
Refinish receiver.
Lap the bore.
Clean up the muzzle crown.
Lap the barrel shoulder to the receiver.
Modify bolt for smoother action.
Perform a trigger job.
Reassemble the rifle with dry-firing firing pin.
Glass bed the fore end to remove looseness and refinish.
Replace and install the sights.
Fill chips in butt stock.
Replace and fit new butt plate.
Refinish butt stock.
Add a saddle ring.
Inlet a Morgan silver dollar into the butt stock.

Remove Sights
Removing the sights was easy; they tapped right out from left to right with a brass punch.The front dovetail on the front sight was peened up because the sight was installed incorrectly, so I took a punch and flattened as much of the raised lip as I could.

Completely Disassemble the Rifle
I completely disassembled the rifle and found no rust inside.This was good news!Some screw-heads wer

Ted Williams Model 100 Serial Numbers